2014 Acura TSX Alignment in Marietta, GA | Nalley Acura

About 60 minutes.

At Nalley Acura in Marietta, most four-wheel alignments for the 2014 Acura TSX are completed in roughly an hour when there are no additional suspension repairs needed. Technicians begin with an inspection, make precise caster/camber/toe adjustments to factory targets, and perform a road test to confirm steering feel and tracking.

• Initial suspension inspection and tire pressure check
• Adjust caster, camber and toe to factory settings using OEM equipment
• Final road test and printed before/after alignment readings

Get an alignment every 2–3 years or about every 30,000 miles, and after suspension work or a major impact.

Georgia roads and seasonal roadwork can accelerate steering and tire wear; check alignment sooner if you hit large potholes or curbs. Nalley Acura inspects your TSX’s suspension components during the alignment and will recommend repairs if worn parts prevent the alignment from holding.

• Schedule alignment after tire replacement or rotation if you notice uneven wear
• Re-check alignment after suspension repairs or collision work
• Consider an inspection after significant pothole or curb impacts common on North Atlanta roads

Look for uneven tire wear, the vehicle pulling to one side, an off-center steering wheel, or vibration at highway speeds.

Those symptoms often show before visible tire damage. Nalley Acura’s technicians inspect tires, tie rods, and suspension components to determine whether the issue is an alignment or a worn part that must be repaired first.

• Inner or outer tire tread wearing faster than the rest of the tire
• Car drifts left or right on a flat, straight road
• Steering wheel not centered when driving straight

A full four-wheel alignment includes caster, camber and toe adjustments to factory specifications plus a suspension inspection and printed before/after readings.

Nalley Acura technicians use OEM-grade alignment lifts and computerized alignment heads to measure and set the TSX to Acura factory targets. The process identifies worn components that could prevent the alignment from staying in spec and includes a final road test to confirm handling.

• Measure and adjust front and rear caster, camber and toe to factory specs
• Inspect tie rods, ball joints, control arms and shocks/struts for wear
• Provide printed before/after alignment readings and a post-service road test

If worn tie rods, ball joints, or damaged struts are present, an alignment alone will not correct the problem; Nalley Acura inspects suspension parts first.

When alignment settings don't hold or irregular tire wear continues after adjustment, worn suspension components are usually the cause. Our technicians check component wear and provide a clear repair recommendation so the TSX can return to factory alignment once defective parts are addressed.

• Evidence of play in tie rods or ball joints during inspection
• Damaged or leaking shocks/struts that affect ride height and alignment angles
• Frame or control-arm damage found after an impact that requires repair before alignment

Not always; if your TSX tracks straight with even tire wear, you can defer a full alignment until scheduled intervals or after repairs—unless you notice symptoms.

A proactive alignment after noticeable events—tire replacement, suspension work, or a pothole impact—helps preserve tire life and handling. Nalley Acura can perform a suspension check and provide a recommended service plan based on condition and local driving conditions in North Atlanta.

• Inspect tires and steering if you feel vibration or pull despite straight tracking
• Align after new tires are installed to prevent uneven wear
• Use Nalley Acura’s scheduling tool to book an inspection: schedule service

Factory specifications for caster, camber, and toe are applied to both front and rear suspension locations using OEM procedures and computerized alignment equipment. Nalley Acura verifies ride height and suspension geometry before making adjustments; if ride height or worn components are outside tolerance, those conditions are documented and repaired to ensure the TSX can be returned to factory alignment targets.

We use Acura-approved measurement tools and record before/after printouts so adjustments can be validated against factory settings. Common local callouts include pothole impacts and curb strikes that alter toe angles or camber; when we find those issues we recommend the appropriate repairs so the alignment holds.

Bring your 2014 Acura TSX to Nalley Acura in Marietta for a factory-spec alignment — schedule service.

Nalley Acura serves Marietta and nearby communities including Roswell, Alpharetta, Milton, Johns Creek, Sandy Springs, and the wider North Atlanta area. Local roads, construction, and seasonal potholes can change alignment angles over time; our technicians inspect the entire steering and suspension system and test the vehicle on local road conditions to confirm handling and steering response.

We document suspension findings, adjust caster/camber/toe to factory specifications, and provide a thorough before/after report. If your TSX needs additional repairs, we’ll explain the issue and outline required work so your vehicle returns to stable, predictable handling.

For appointments and current offers, view our service specials or schedule service online.

A standard four-wheel alignment for the 2014 Acura TSX includes a step-by-step inspection and adjustment process: initial vehicle and tire inspection, measurement of caster/camber/toe, adjustment to Acura factory targets, and a final road test with printed before/after measurements. Our technicians also check tire pressures, steering linkage, and suspension components that could prevent the alignment from remaining in spec.

When corrective parts are required, we provide a clear repair estimate. If you want to confirm cost-savings options, check our current service specials. To book an appointment, schedule service online.